EK Water Blocks EK-Supremacy Manuel d'installation télécharger pdf (Page 2)

All disclosures, notices and warranty conditions are being written on the back of the box. Revision 1.0. Released on 30

of May, 2012.

STEP 5: INSTALLING THE WATER BLOCK:

STEP 5a: Intel LGA-1366 and AMD socket motherboard:

1) Place motherboard on an even surface with front facing down.

2) Install backplate rubber gasket - depending on your CPU platform (

see STEP 4)

and place metal backplate for Intel LGA-1366 and AMD socket to the back of your

motherboard. Align the holes on the motherboard with holes on rubber gasket

and backplate.

3) Carefully rotate motherboard assembly with front side facing up with one hand

while holding the backplate and rubber in place with the other hand.

4) Install the rest of mounting system as per installation manual

(see STEP 6)

STEP 5b: Intel LGA-115x socket motherboard:

1) Place motherboard on an even surface with front facing down.

2) Install backplate rubber gasket - depending on your CPU platform (

see STEP 4)

and place metal backplate for Intel LGA-115x socket to the back of your

motherboard. Align the holes on the motherboard with holes on rubber gasket

and backplate. Make sure to orientate the rubber gasket to fit past the

CPU socket ILM backplate.

3) Carefully rotate motherboard assembly with front side facing up with one

hand while holding the backplate and rubber in place with the other hand.

4) Install the rest of mounting system as per installation manual

(see STEP 6)

STEP 5c: Installing the mounting system:

Intel Socket LGA-115x/1366 and AMD sockets:

Install the M4 thumb screws of the PreciseMount mounting system onto your

motherboard. It is mandatory to put 0.7mm plastic washer underneath each of

the M4 thumb screws. Tighten the M4 thumb screw to the metal backplate with

your hands until you reach the end of the thread. Using tools (such as pliers) is

not recommended!

Intel Socket LGA-2011:

Install four (4) specific LGA-2011 M4 thumb screws into four M4 threaded stubs

on the LGA-2011 socket integrated latch mechanism (ILM). The screws are to be

installed using no tools (i.e. pliers).

STEP 5d: Preparing your CPU and applying TIM:

Cleaning the CPU: Once mounting mechanism is attached install the CPU into

the socket. Wipe the CPU’s contact surface (by using non–abrasive cloth or

Q-

tip

, as shown on sample photo).

Applying thermal compound: EK recommends blob or line method of

applying the enclosed Gelid GC-Extreme™ thermal compound to the CPU

heatspreader (IHS) - see sample photo on right. The quantity of about two rice

grains is just about right. There is no need to cover the whole IHS. Applying too

much thermal grease will have negative impact on the cooling performance!

STEP 5e: Fastening the waterblock:

Install the waterblock on your CPU. Place an enclosed compression spring and

thumb nut over each M4 thumb screw. Start fastening two thumb nuts at a time,

preferably in cross pattern and do not tighten them fully until all of them are

partially screwed in. Then - using your fingers only - screw in all four thumb nuts

until you reach the end of the thread.

STEP 6: CONNECTING WATER BLOCK TO THE COOLING CIRCUIT

Carefully identify the direction of the flow in your circuit. For the EK-Supremacy

series water block to operate properly the G1/4 port nearest to the center of the

water block MUST BE USED AS THE INLET PORT. EK recommends the use of

EK-PSC fittings. When using fittings other than EK-PSC series please use hose

clamps or appropriate substitute to secure the tubing to the barb. The use of

biocide containing and corrosion inhibiting coolant is always recommended for

any liquid cooling system.

REQUIRED TOOLS

- allen key 2.5mm (enclosed)

figure 1: Isometric view of backplate assembly for LGA-1366

Metal backplate

Rubber gasket

Motherboard

PCB

figure 2: Isometric view of backplate assembly for LGA-115x

Metal backplate

Rubber gasket

Motherboard

PCB

M4 thumb screw

PVC washer

LGA 2011 M4

thumb screw

Thumb nut

Coiled spring

EK-PSC fitting

Tubing

1 2

1
of May, 2012 2

Commentaires sur ces manuels

Pas de commentaire

EK Water Blocks EK-Supremacy Manuel d'installation Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Refroidissement des ordinateurs par liquide EK Water Blocks EK-Supremacy